Frequently Asked Questions
If you have any questions or concerns, please do not hesitate to contact us.
We would love to hear from you, contact us at [email protected]


1. Before adding bait, turn the switch to the off (“0”) position.
2. Pull and remove the top chamber. Use only a pea-sized amount of peanut butter in the bait area. Do not let the bait touch the metal plate surfaces or the sensor detectors, as it may cause a malfunction.
3. Attach the top chamber back into place. Insert 4 “aa” batteries and turn the switch to the on (“i”) position. The green light will flash to indicate the trap has been activated. Place the trap on a clean, dry surface along a wall. Position the trap so that the entrance is facing away from the wall.
4. Once a rodent is caught, the green light will flash at 10-second intervals. A flashing red light indicates low battery life.
5. Rodent disposal: turn the switch to off (“0”) and remove the batteries. Pull and remove the top chamber and properly discard the rodent. Follow the cleaning instructions on the trap or in the manual.
1. Before adding bait, turn the switch to the off (“0”) position.
lift open the bait door and use only a pea-sized amount of peanut butter in the bait area. Do not let the bait touch the metal plate surfaces or the sensor detectors, as it may cause a malfunction.
2. Close the bait door. Insert 4 “c” batteries and turn the switch to the on (“i”) position. The green light will flash to indicate the trap has been activated.
place the trap on a clean, dry surface along a wall. Position the trap so that the entrance is facing away from the wall.
3. Once a rodent is caught, the green light will flash at 10-second intervals.
4. A flashing red light indicates low battery life.
5. Rodent disposal: turn the switch to off (“0”) and remove the batteries. Pull and remove the top chamber and properly discard the rodent. Follow the cleaning instructions on the trap or in the manual.
Turn the switch to off (“0”). Pull and remove the top of the trap, then properly discard the rodent. Follow the cleaning instructions of the trap in the manual.
Mouse trap/rat trap
1. Turn the switch off (“0”) and remove the batteries. Pull and remove the top chamber.
2. Clean: use warm water or hydrogen peroxide topical solution and a soft-bristle brush to clean the chamber. Do not get any water on the electronic top.
3. Dry: air dry the interior and exterior chamber completely. Dry hands thoroughly.
4. Reassemble: attach the top back into place.
5. Reload: repeat the trap use instructions from steps 1-4.
Q: How do you dispose of the dead rodent?
A: Turn the switch to off (“0”). Pull and remove the top of the trap, then properly discard the rodent in an outdoor trash bin.
Q: How do you replace the batteries?
A: Turn the switch to off (“0”) and insert 4 aa batteries into the compartment.
Q: What type of batteries do you need?
A: 4 “aa” for the mouse trap. 4 “cc” for the rat trap.
Q: Green led keep flushing, but doesn't catch rats, then how to reset the device?
A: Try resetting the device.Just turn off the switch,reset the trap again by following how to set up steps1-5.
Q: How do i know the trap has activated?
A: Turn the switch to the on (“i”) position. The light will flash green for one second to indicate that it has been activated.
Q: What If The Trap Is In The Attic? Does It Make A Sound To Indicate That Something Has Been Caught?
A: This trap is designed with a led light to notify you of a kill. A blinking green light means a mouse has been caught. We recommend checking the trap frequently.
Q: How many volts does this deliver? Is it enough to kill large rats?
A: This trap provides a shock of about 5,000-8,000 volts for 30 seconds, which is enough to kill most common rat species.
Q: What is the warranty on this?
A: This product has a 30-day guarantee and a 1-year warranty from the purchase date with a copy of the receipt.
Q: Does the trap come with batteries?
A: Batteries are not included.
Q: Can i use this outside?
A: No, it is not weatherproof. But you could use it in any area shielded from water.
Q: What baits should i use in the mouse traps?
A: Peanut butter, chocolate, gumdrops, soft cheese, nuts, and oats work best.
Q: How much bait should i use in the traps?
A: A small pea-sized amount should be placed in the bait area inside the trap.
Q: How do i safely clean the trap?
A: Remove the top of the trap. Use warm water, soft bristle brush, and hydrogen peroxide topical solution only. Do not get water on electronic top.
allow interior and exterior to air dry completely. Dry hands thoroughly before reassembling. To reassemble, simply attach the top back into place.
Q: Where should i place my mouse traps?
A: Place the trap on a clean, dry surface along a wall near signs of rodent activity.
1.Please use good quality Alkaline batteries , do not use carbon batteries and rechargeable batteries.
2.Please use it in a dry place indoors, avoid using it outdoors.
3.After power-on, the green light will be on for 1 second, indicating that the battery is normal, and then it will go out and enter the low-power standby detection state. If the battery is low power, the red light will continue to flash quickly after power-on, until the battery is replaced.
4.After turning on the device, the green light is always on for 1 second, if the red and green lights continue to flash synchronously. It means that the device has failed to self-check. Please refer to the instructions . Check whether the two sets of infrared probes are blocked by bait or other foreign objects, and whether the metal plate is wet.
5.Because this product has a certain function of protecting pets, some larger mice or small animals will also be protected as a pet and will not be killed. So when you find that bait is often stolen, may be there is a big mouse or a small animal of similar size nearby.
1. Add a small amount of bait using a cotton swab or toothpick. The built-in bait cup makes it easy to hold high-protein substances. Peanut butter or chocolate is best for luring the mouse to the trap.
2. Carefully move the hammer bar to the back of the trap and latch it under the lock hook. Caution: do not touch the trigger pedal.
3. Place the trap wherever you see signs of rodent activity. Position the trap with the trigger end (bait cup) up against the wall. You’re all set!
1. It’s best to place two traps 5-10ft apart to cover more of an area and increase the potential to catch rodents.
2. Place the traps in target areas with high mouse activity where smudge marks, tracks, or droppings are discovered.
3. Make sure that all other competitive foods sources in your home are kept to a minimum and/or out of reach from rodents to the best of yourt abiliiesy.
Q: How do i set the trap?
A: Make sure to read all of the instructions carefully. Follow the instructions on the packaging in order, step by step.
Q: What kind of bait do i use?
A: Food that’s high in protein such as peanut butter, chocolate, hazelnut spread, or meat (bacon, for example).
Q: Can the trap be used more than one time?
A: Yes, you may clean and reuse the trap as long as it is not damaged. Please wear disposable gloves and take sall afety precautions when installing or recovering any traps.
Q: If i reuse the trap, how should i clean it?
A: We recommend cleaning the trap with bleach wipes and then using unscented antibacterial dish soap and warm soapy water.
Q: Would a dead mouse's scent cause another mouse to avoid the same trap?
A: The smell of a dead mouse would entice others to go to the trap or area where the smell is.
Q: What should i do if the mice keep stealing the bait from the trap?
A: If bait is being stolen, make sure the trap is functioning properly by checking that the power source is full and the trap is turning on. Also, use only a very small amount of bait to attract the rodent. Using too much bait can cause the trap’s trigger to fail.


Simply plug the Ultrasonic Rodent Repeller into a wall outlet, and you're set! The repeller comes with a built-in night light that provides a soft glow and lets you know when it's working. High-frequency sound can not penetrate walls and solid objects, so it's best to use the repeller in an open space and clear all surroundings before use. To repel larger populations of rodents, use the device in conjunction with traps and baits.
Q: How do I know the repeller is on?
A: When powered up, the white light will be visible, indicating the device is working and broadcasting the high-frequency waves
Q: The night light stopped working. Is the ultrasonic repeller still working?
A: If the light is out, the repeller is no longer working and should be replaced.
Q: How long until I see results?
A: Allow 2-4 weeks for ultrasonic sound waves to affect pests with an established food source. For established infestations, it is necessary for you also to use baits and traps to reduce the population.
Q: Is ultrasonic sound safe for pets?
A: The device emits a frequency of 32-62 kHz, well above the range of hearing for humans and non-rodent pets like cats, dogs, birds, and fish. If you have rodent pets such as a hamster or guinea pig, please move your pet to a room without the device.
Q: When can i get the refund?
A: Put the answer of Frequently Asked Questions here to help customer get more info about your product / service. It will increase reliability for your store as well as help you save a lot of time to answer repeated question from your buyer.
Q: Does this work against rats?
A: The Ultrasonic Rodent Repeller is effective against mice, rats, and other types of rodents.
Q: Is the repeller useful against insects too?
A: No, we suggest using the repeller only for rodents, mice, and rats.
Q: What are the most common mistakes people make with repellents?
A: A common mistake is using ultrasound units alone to control an established infestation, especially when the room has sufficient food and a comfortable temperature. You would have to use traps and baits in conjunction with ultrasonic devices. Most people don't know that ultrasound can not travel through walls, so it is essential to place at least one repeller in each room and away from solid objects.
Q: Can the repeller interfere with other equipment?
A: No, it will not interfere with pacemakers, garage door openers, or any other electronic equipment.
Q: Where should I place the repeller?
A: It is ideal to place the repeller in medium-sized rooms that have signs of rodent activity. Look for signs of an infestation such as chewing or gnaw marks, droppings, tracks, and nests.
1. Before adding bait, turn the switch to the OFF ( “0” ) position.
2. Put the bait into the bait cup.
3. Insert 4 “D” batteries or connect the USB cord to the power source. Then turn on the switch to the ON ( “I” ) position.
4. Cover the top of the trap with a waterproof cover when you use it outdoors.
5. Place the trap along a wall indoor or outdoor where you are experiencing rodent problems. Position the trap with entrance outwards.
1. When used outdoors, please check the product status regularly, especially after rain.
2. Change the bait in time, so as to prevent the bait from going bad or being eaten by other animals, which will affect the product efficiency.
3. It is recommended to place it against a wall, not in low-lying places where water is easy to accumulate.
4. If infrared probe is soaked in water, the red and green light will be on at the same time. Please then separate the top and bottom part, clean and dry the probe in time.
5.The product shall not be soaked in water to avoid functional damage.
6.When use USB for power, please take out the batteries. Also when use the batteries, please unplug the USB cord from the electricity. This suggestion is for saving the energy of the batteries.